Thermo Scientific MaxQ 7000 Water Bath Shaker - Digital
Part Number: SHKE7000 (120V) - or - SHKE7000-1CE (240V)
SHKE7000 Water Bath Shaker
You'll get unmatched power, accuracy, and reproducible results with Thermo Scientific MaxQ shakers, and more. In fact, once they're set up in your lab, you'll see how the long list of innovative product features translates to multiple benefits for your team, assuring you effectiveness, efficiency, and productivity.
Triple eccentric drive mechanism gives you continuous 24-hour operation and allows you to shake and stir large and uneven loads, smoothly and uniformly. Plus, it's guaranteed for life.
Easy access drain with quick disconnect located in the front of the cabinet for convenience in draining and disinfecting
Alarm alerts operator in case of low water level.
Temperature range of 5°C above ambient to 65°C.
Prevent heat loss and minimize evaporation with use of optional covers. See Accessories Below
Minimize splashing and turbulence in chamber with twin baffles even at high speeds.
Optional cooling coil extends the range of applications to near and below ambient. See Accessories for cooling coil option.
Monitored and controlled temperature with ±0.2°C accuracy at 37°C
Over-temperature safety feature with independent thermostat provides additional backup by controlling heat if main temperature controller fails
Applications: Cell culture, Solubility studies, Extraction procedures, Diagnostic tests, General mixing, Bacterial suspensions, Staining and destaining, Washing procedures, Hybridization
Digital Operating System
Variable speed control from 15 to 500 rpm
Continuous/timed operation from 0.1 hour to 999 hours or 0.1 minute to 999 minutes.
View speed, operating time and temperature simultaneously on three individual LED displays.
Visual/audible alarms alert you to temperature deviations. Heat turns off if temperature deviates ±1°C of set point.
Shaker shuts down and visual/audible alarms signal if unit operates ±10% of set speed, preventing shaker from walking.
User-adjustable speed calibration can be performed using a digital handheld tachometer, where verification is required and protocols can be standardized.
Unbalanced load sensor stops platform motion when excess vibration is detected and visual/audible alarms signal until condition is corrected.
Soft start feature eliminates sudden starts and stops, splashing of vessel contents or wetting of flask closure.
Retains parameters during power failure and restarts unit automatically after power is restored.
Platforms for SHKE7000
Universal platforms allow you to place different sizes of labware on a single platform. Clamps for various flask and test tube sizes hold the labware in place. After selecting a platform, purchase clamps below or use our MaxQ 7000 Clamp Guide.
Dedicated platforms come installed with the maximum capacity of clamps for the designated labware size. The platform is ready to be used.
11" x 13" Dedicated Platforms
Clamps for SHKE7000
Clamps fit on the Universal Platforms holding the labware in place and accommodate various flask and test tube sizes. The platform will hold all sizes, so you can mix and match clamps for the various labware you have. Each clamp is sold separately.
Max Clamp Capacity per Platform
Part Number: 30129
Includes (1) microplate clamp, (2) 125ml flask clamps, (4) 250ml flask clamps, (4) 500ml flask clamps, (2) 1L flask clamps, and (2) 2L flask clamps.
Part Number: 3540-46
A utility tray platform does not accept or require clamps. It provides a non-slip surface to hold petri-dishes, Pyrex dishes, microplates and smaller flasks at low RPM's. The maximum shaking speed is 150 rpm.
Part Number: 3540-49
Dedicated Basket Platform with Retainer Springs 11x13
Part Number: SHK7000-37
A cooling coil is needed to reach and maintain near-ambient and below temperatures in the chamber. Please note that a circulating chiller is required. Search our site for item SHK4450CH if you do not have a chiller.
Part Number: SHK7000-30
A gable cover minimizes heat loss and evaporation. The stainless steel model is required for temperatures up to 90 degree C.
Part Number: SHK7000-32
A gable cover minimizes heat loss and evaporation. The Plexiglas model is required for temperatures up to 65 degree C.
Part Number: SHK7000-40
The suspension arms can be placed on another platform so that you can quickly change out your existing platform. Attach the arms to an additional platform and have that one ready and loaded to swap out rather than having to drain, change clamps, add flasks, etc.
Part Number: SHK7000-45
Ideal for under lab bench operation, the movable dolly allows you to easily roll the shaker.
Part Number: SHK4450CH
A chiller is used in conjunction with the incubated shaker to achieve temperatures from 20 degrees to 30 degrees celsius. This makes the incubated shaker refrigerated.